Omnia Omnia.9sg


Omnia.9 Technology in a 1RU Standalone Stereo Generator

In some applications, it might make
more sense to locate the main audio processor at the studios while the
stereo generator and limiter live out at the transmitter site. This
might include cases where the STL uses discrete analog or AES audio
rather than composite, or situations where one primary audio processor
feeds multiple sites such as satellite distribution.

Omnia.9sg brings the same acclaimed
clipper, limiter, and stereo generator technology in the Omnia.9 to a
standalone box—but that isn’t all it does…We brought a few other tricks
from the Omnia.9 along for the ride.


  • Psychoacoustic Composite Embedder allows up to 140% audio peaks in stereo at 100% total modulation.
  • Full IP remote control with remote audio streaming
  • Optional RDS encoder
  • Selectable SSB (Single Sideband) stereo encoder
  • Analysis tools for internal or external composite signals


Psychoacoustic Distortion Masking Clipper

As with the Omnia.9, the
psychoacoustic distortion-masking clipper built into the Omnia.9sg
allows for incredibly loud audio without distortion. It allows 140%
audio peaks at 100% modulation, even with 75 microsecond pre-emphasis

ITU-BS.412 MPX Power Controller

With all of this capability for
ultimate loudness and modulation, the ITU-BS.412 MPX Power Controller
ensures you remain compliant with applicable regulations while still
producing competitively loud yet clean audio.

Auto Pilot

Another feature carried over from the
Omnia.9 into the 9sg is the unique “Auto Pilot” function. Turning off
the stereo pilot during mono programming allows for a 12 dB
signal-to-noise improvement when it counts the most. Auto Pilot will
automatically suppress the 19 kHz stereo pilot during mono programming
ensuring that your programming stays as noise-free as possible.

Full Remote Control

While the front panel LCD allows basic
configuration and monitoring, the Omnia.9sg has a complete IP remote
control interface. NF Remote software (also used with many other Telos
Alliance products) can control the unit and access the same full suite
of test instrumentation available in the Omnia.9. External composite
signals from modulation monitors can also be analyzed and streamed
through the remote software for off-air monitoring


Frequency Response:

  • +/- .5 dB 20 Hz to 15 kHz

Signal-Noise Ratio: 

  • Greater than -80 dBu de-emphasized, 20 Hz to 15 kHz

Stereo Separation: 

  • 65dB minimum, 20 Hz to 15 kHz, 70 dB typical

Stereo Baseband Output:

  • Adjustable from -2 dBu to +22 dBu (0.1 dB increments) into 600-Ohms, 20-Ohm output impedance

Analog Inputs: 

  • Two balanced, EMI filtered XLR connectors

Digital Inputs: 

  • AES/EBU In & External Sync

Composite I/O: 

  • Four 75-Ohm BNC female, two inputs, two outputs

Remote Control: 

  • RJ45 supporting 100 Base-T Ethernet connections

Power Requirements: 

  • 100-264 VAC, 47-63 Hz autosensing

Power Connector: 

  • IEC male, detachable 3-wire power cord supplied


  • Operating: 0 to 50 degrees C
  • Non-Operating: -20 to 70 degrees C


  • North America: FCC and CE tested and compliant, power supply is UL approved
  • Europe: Complies with
    the European Union Directive 2002/95/EC on the restriction of the use
    of certain hazardous substances in electrical and electronic equipment
    (RoHS), as amended by Commission Decisions 2005/618/EC, 2005/717/ EC,
    2005/747/EC (RoHS Directive), and WEEE.

For a Quote or to place an order, please contact us as follow;

P: +44 (0)1444 473999